• ioLogik R1200 Series

RS-485 remote I/O

Features and Benefits

  •  Dual RS-485 remote I/O with built-in repeater
  •  Supports the installation of multidrop communications parameters
  •  Install communications parameters and upgrade firmware via USB
  •  Upgrade firmware through an RS-485 connection
  •  Wide operating temperature models available for -40 to 85°C (-40 to 185°F) environments

    Introduction

    The ioLogik R1200 Series RS-485 serial remote I/O devices are perfect for establishing a cost-effective, dependable, and easy-to-maintain remote process control I/O system. Remote serial I/O products offer process engineers the benefit of simple wiring, as they only require two wires to communicate with the controller and other RS-485 devices while adopting the EIA/TIA RS-485 communication protocol to transmit and receive data at high speed over long distances. In addition to communication configuration by software or USB and dual RS-485 port design, Moxa’s remote I/O devices eliminate the nightmare of extensive labor associated with the setup and maintenance of data acquisition and automation systems. Moxa also offers different I/O combinations, which provide greater flexibility and are compatible with many different applications.

    • Buttons

       

      Reset button

    • Analog Input Channels

       

      ioLogik R1240 Series: 8

    • Analog Output Channels

       

      ioLogik R1241 Series: 4 

    • Configurable DIO Channels (by software)

       

      ioLogik R1212 Series: 8

    • Digital Input Channels

       

      ioLogik R1210 Series: 16
      ioLogik R1212 Series: 8
      ioLogik R1214 Series: 6

    • Isolation

       

      3k VDC or 2k Vrms

    • Relay Channels

       

      ioLogik R1214 Series: 6

    • Connector

       

      Screw-fastened Euroblock terminal

    • Counter Frequency

       

      2.5 kHz

    • Digital Filtering Time Interval

       

      Software configurable

    • Dry Contact

       

      On: short to GND
      Off: open

    • I/O Mode

       

      DI or event counter

    • Points per COM

       

      ioLogik R1210/R1212 Series: 8 channels
      ioLogik R1214 Series: 6 channels

    • Sensor Type

       

      Dry contact
      Wet Contact (NPN or PNP)

    • Wet Contact (DI to COM)

       

      On: 10 to 30 VDC
      Off: 0 to 3 VDC

    • Connector

       

      Screw-fastened Euroblock terminal

    • Current Rating

       

      200 mA per channel

    • I/O Mode

       

      DO or pulse output

    • I/O Type

       

      Sink

    • Pulse Output Frequency

       

      5 kHz

    • Over-Current Protection

       

      0.65 A per channel @ 25°C

    • Over-Temperature Shutdown

       

      175°C (typical), 150°C (min.)

    • Over-Voltage Protection

       

      45 VDC (typical)

    • Breakdown Voltage

       

      500 VAC

    • Connector

       

      Screw-fastened Euroblock terminal

    • Contact Current Rating

       

      Resistive load: 5 A @ 30 VDC, 250 VAC, 110 VAC

    • Contact Resistance

       

      100 milli-ohms (max.)

    • Electrical Endurance

       

      100,000 operations @ 5 A resistive load

    • Initial Insulation Resistance

       

      1,000 mega-ohms (min.) @ 500 VDC

    • Mechanical Endurance

       

      5,000,000 operations

    • Pulse Output Frequency

       

      0.3 Hz at rated load

    • Type

       

      Form A (N.O.) power relay

    • Note

       

      Ambient humidity must be non-condensing and remain between 5 and 95%. The relays may malfunction when operating in high condensation environments below 0°C.

    • Accuracy

       

      ioLogik R1240:
      ±0.1% FSR @ 25°C
      ±0.3% FSR @ -10 to 60°C

      ioLogik R1240-T:
      ±0.1% FSR @ 25°C
      ±0.3% FSR @ -10 to 60°C
      ±0.5% FSR @ -40 to 75°C

ioLogik R1200 Series

  • Brand: MOXA
  • Product Code: ioLogik R1200 Series
  • Availability: Please email - info@cayee.com.hk