• VPort 464 Series

Superior video performance, 4-channel industrial video encoders

Features and Benefits

  •  Each channel supports 2 D1 30 fps streams simultaneously, or merge 1 quad stream 30 fps image into 4 channels
  •  Video latency under 200 ms
  •  2 Ethernet ports for cascading or Ethernet port redundancy
  •  DynaStream™ for optimized network efficiency
  •  ONVIF support for standardization and interoperability
  •  Local storage capability with microSD card slot
  •  Industrial design with -40 to 75°C operating temperature

    Introduction

    The VPort 464 4-channel industrial video encoder uses the H.264 video compression algorithm to provide the best video quality on the market, but with a smaller bandwidth requirement than other video compression standards. In addition, to meet various requirements, each channel of the VPort 464 can support 2 video streams simultaneously or you can merge all 4 channels into 1 quad view stream using H.264 and MJPEG compression formats, providing greater flexibility for a variety of uses, including viewing, recording, and analysis. The rugged industrial design, which includes a -40 to 75°C operating temperature, IP30 protection, and industrial certifications, make the VPort 464 suitable for harsh environments.

    The VPort 464 comes with two Gigabit Ethernet ports and supports cascade mode and network redundancy. In addition, Moxa’s innovative DynaStream™ technology lets you change the video frame rate automatically, allowing you to control your network bandwidth budget and simplify network system management. The CBR Pro™ function guarantees the lowest packet loss for limited bandwidth transmissions to ensure that images will not exhibit the mosaic effect.

    • microSD Slot

       

      SDXC

    • Digital Input Channels

       

      4

    • Digital Inputs

       

      +13 to +30 V for state 1
      -30 to +1 V for state 0
      Max. input current: 8 mA

    • Relay Channels

       

      2

    • Contact Current Rating

       

      Resistive load: 1 A @ 24 VDC

    • Connector

       

      Terminal block

    • 10/100BaseT(X) Ports (RJ45 connector)

       

      2

    • Protocols

       

      TCP/IP, IPv4/IPv6, UDP, HTTP, RTP/RTSP, ARP, UPnP, FTP, TFTP, SMTP, NTP Client, DNS, DDNS, QoS, IGMP v3, ICMP, SNMPv1/v2c/v3, Modbus TCP, HTTPS, 802.1X, NTCIP

    • Password

       

      User-level password protection

    • Filter

       

      IP address

    • Authentication

       

      802.1X

    • Encryption

       

      HTTPS

    • LED Indicators

       

      STAT: Indicates if system is booted up properly or not
      Power 1: Power 1 on/off
      Power 2: Power 2 on/off
      FAULT: Can be configured to correspond to system alarm, power failure, or disconnected network
      Video: Video input signal
      PTZ: Indicates if PTZ or COM port data has been transmitted
      SD: Indicates if SD card was mounted successfully
      Network: 10 Mbps or 100 Mbps

    • PTZ Port

       

      1, RS-232 or RS-422/485 port, terminal block connector, 115.2 kbps

    • COM Port

       

      1, RS-232 or RS-485 port, DB9 male connector, 115.2 kbps

    • Console Port

       

      1 RS-232 port, 10-pin RJ45 (115200, n, 8, 1)

    • No. of Power Inputs

       

      2

    • Input Voltage

       

      Redundant dual inputs

    • Operating Voltage

       

      12 to 32 VDC, 18 to 30 VAC

    • Input Current

       

      0.5 A @ 24 VDC
      0.83 A @ 24 VAC

    • Power Connector

       

      2-pin terminal block

    • Video Compression

       

      H.264 (ISO/IEC 14496-10) or MJPEG

    • Video Input

       

      4, BNC connector (1.0 Vpp, 75 ohm)

    • Video Output

       

      via Ethernet

    • Video Streams

       

      2 independent H.264 or MJPEG video streams
      1 quad (4-channel images) stream

    • NTSC/PAL

       

      Auto-sensing or manual

VPort 464 Series

  • Brand: MOXA
  • Product Code: VPort 464 Series
  • Availability: Please email - info@cayee.com.hk