• MGate 5118 Series

1-port CAN-J1939 to Modbus/PROFINET/EtherNet/IP gateways

Features and Benefits

  •  Converts J1939 to Modbus, PROFINET, or EtherNet/IP
  •  Supports Modbus RTU/ASCII/TCP master/client and slave/server
  •  Supports EtherNet/IP Adapter
  •  Supports PROFINET IO device
  •  Supports J1939 protocol
  •  Effortless configuration via web-based wizard
  •  Built-in Ethernet cascading for easy wiring
  •  Embedded traffic monitoring/diagnostic information for easy troubleshooting
  •  microSD card for configuration backup/duplication and event logs
  •  Status monitoring and fault protection for easy maintenance
  •  CAN bus and serial port with 2 kV isolation protection
  •  -40 to 75°C wide operating temperature models available
  •  Security features based on IEC 62443

    Introduction

    The MGate 5118 industrial protocol gateways support the SAE J1939 protocol, which is based on CAN bus (Controller Area Network). SAE J1939 is used to implement communication and diagnostics among vehicle components, diesel engine generators, and compression engines, and is suitable for the heavy-duty truck industry and backup power systems. It is now common to use an engine control unit (ECU) to control these kinds of devices, and more and more applications are using PLCs for process automation to monitor the status of J1939 devices connected behind the ECU.

    The MGate 5118 gateways support the conversion of J1939 data to Modbus RTU/ASCII/TCP, EtherNet/IP, or PROFINET protocols to support most PLC applications. Devices that support the J1939 protocol can be monitored and controlled by PLCs and SCADA systems that use the Modbus RTU/ASCII/TCP, EtherNet/IP, and PROFINET protocols. With the MGate 5118, you can use the same gateway in a variety of PLC environments.

    • 10/100BaseT(X) Ports (RJ45 connector)

       

      2
      Auto MDI/MDI-X connection

    • Magnetic Isolation Protection

       

      1.5 kV (built-in)

    • Industrial Protocols

       

      Modbus TCP Client (Master), Modbus TCP Server (Slave), PROFINET IO Device, EtherNet/IP Scanner, EtherNet/IP Adapter

    • Configuration Options

       

      Web Console (HTTP/HTTPS), Device Search Utility (DSU), Telnet Console

    • Management

       

      ARP, DHCP Client, DNS, HTTP, HTTPS, SMTP, SNMP Trap, SNMPv1/v2c/v3, TCP/IP, Telnet, SSH, UDP, NTP Client

    • MIB

       

      RFC1213, RFC1317

    • Time Management

       

      NTP Client

    • Console Port

       

      RS-232 (TxD, RxD, GND), 8-pin RJ45 (115200, n, 8, 1)

    • No. of Ports

       

      1

    • Connector

       

      DB9 male

    • Serial Standards

       

      RS-232/422/485

    • Baudrate

       

      50 bps to 921.6 kbps

    • Data Bits

       

      7, 8

    • Parity

       

      None, Even, Odd, Space, Mark

    • Stop Bits

       

      1, 2

    • Flow Control

       

      RTS Toggle (RS-232 only), RTS/CTS

    • Pull High/Low Resistor for RS-485

       

      1 kilo-ohm, 150 kilo-ohms

    • Terminator for RS-485

       

      120 ohms

    • Isolation

       

      2 kV

    • RS-232

       

      TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND

    • RS-422

       

      Tx+, Tx-, Rx+, Rx-, GND

    • RS-485-2w

       

      Data+, Data-, GND

    • RS-485-4w

       

      Tx+, Tx-, Rx+, Rx-, GND

    • Configuration Options

       

      Serial Console

    • Industrial Protocols

       

      J1939, Modbus RTU/ASCII Master, Modbus RTU/ASCII Slave

    • Mode

       

      Master, Slave

    • Functions Supported

       

MGate 5118 Series

  • Brand: MOXA
  • Product Code: MGate 5118 Series
  • Availability: Please email - info@cayee.com.hk